lotus/documentation/en/mpool.md

The Message Pool

The Message Pool (mpool) is the component of lotus that handles pending messages for inclusion in the chain. Messages are added to the mpool either directly for locally published messages or through pubsub propagation. Whenever a miner is ready to create a block for a tipset, it invokes the mpool selection algorithm which selects an appropriate set of messages such that it optimizes miner reward and chain capacity.

API

The full node API defines the following methods for interacting with the mpool:

    MpoolPending(context.Context, types.TipSetKey) ([]*types.SignedMessage, error)
    MpoolSelect(context.Context, types.TipSetKey, float64) ([]*types.SignedMessage, error)
    MpoolPush(context.Context, *types.SignedMessage) (cid.Cid, error)
    MpoolPushMessage(ctx context.Context, msg *types.Message, spec *MessageSendSpec) (*types.SignedMessage, error)
    MpoolGetNonce(context.Context, address.Address) (uint64, error)
    MpoolSub(context.Context) (<-chan MpoolUpdate, error)
    MpoolGetConfig(context.Context) (*types.MpoolConfig, error)
    MpoolSetConfig(context.Context, *types.MpoolConfig) error

MpoolPending

Returns the list of messages that are pending for a tipset.

MpoolSelect

Selects and returns a list of pending messages for inclusion in the next block.

MpoolPush

Pushes a signed message to the mpool; returns the CID of the message.

MpoolPushMessage

Atomically assigns a nonce, signs, and pushes a message to the mpool.

The MaxFee field of the spec argument is only used when GasFeeCap/GasPremium fields aren't specified in the message. When maxFee is set to 0, MpoolPushMessage will guess appropriate fee based on current chain conditions.

MpoolGetNonce

Returns the next nonce for the specified sender. Note that this method may not be atomic. Use MpoolPushMessage instead.

MpoolSub

Returns a channel to receive notifications about updates to the message pool. Note that the context must be cancelled when the caller is done with the subscription.

MpoolGetConfig

Returns (a copy of) the current mpool configuration.

MpoolSetConfig

Sets the mpool configuration to (a copy of) the supplied configuration object.

Command Line Interfae

The lotus command line interface defines an mpool command which allows a user to interact with the mpool.

The following commands are supported:

lotus mpool pending [--local]
lotus mpool sub
lotus mpool stat [--local]
lotus mpool replace [--gas-feecap <feecap>] [--gas-premium <premium>] [--gas-limit <limit>] [from] [nonce]
lotus mpool find [--from <address>] [--to <address>] [--method <int>]
lotus mpool config [<configuration>]

lotus mpool pending

Prints the pending messages in the mpool, as returned by the MpoolPending API call. If --local is specified, it only prints pending messages for addresses in the local wallet.

lotus mpool sub

Subscribes to mpool changes using the MpoolSub API call and prints the stream of mpool updates.

lotus mpool stat

Prints various mpool statistics. If --local is specified then only prints statistics for addresses in the local wallet.

lotus mpool replace

Replaces a message in the mpool.

lotus mpool find

Searches for messages in the mpool.

lotus mpool config

Gets or sets the current mpool configuration.

Configuration

The mpool a few parameters that can be configured by the user, either through the API or the command line interface.

The config struct is defined as follows:

type MpoolConfig struct {
	PriorityAddrs          []address.Address
	SizeLimitHigh          int
	SizeLimitLow           int
	ReplaceByFeeRatio      float64
	PruneCooldown          time.Duration
	GasLimitOverestimation float64
}

The meaning of these fields is as follows:

• PriorityAddrs -- these are the addresses of actors whose pending messages should always be included in a block during message selection, regardless of profitability. Miners should configure their own worker addresses so that they include their own messages when they produce a new block. Default is empty.
• SizeLimitHigh -- this is the maximum number of pending messages before triggering a prune in the message pool. Note that messages from priority addresses are never pruned. Defafult is 30000.
• SizeLimitLow -- this is the number of pending messages that should be kept after a prune. Default is 20000.
• ReplaceByFeeRatio -- this is the gas fee ratio for replacing messages in the mpool. Whenever a message is replaced, the GasPremium must be increased by this ratio. Default is 1.25.
• PruneCooldown -- this is the period of time to wait before triggering a new prune. Default is 1min.
• GasLimitOverestimation -- this is a parameter that controls the gas limit overestimation for new messages. Default is 1.25.

Message Selection

A few words regarding message selection are pertinent. In message selection, a miner selects a set of messages from the pending messages for inclusion to the next block in order to maximize its reward. The problem however is NP-hard (it's an instance of knapsack packing), further confounded by the fact that miners don't communicate their tickets to each other. So at best we can approximate the optimal selection in a reasonable amount of time.

The mpool employs a sophisticated algorithm for selecting messages for inclusion, given the ticket quality of a miner. The ticket quality reflects the probability that a block will execute in the tipset. Given the ticket quality the algorithm computes the probability of each block, and picks dependent chains of messages such that the reward is maximized, while also optimizing the capacity of the chain. If the ticket quality is sufficiently high, then a greedy selection algorithm is used instead that simply picks dependent chains of maximum reward. Note that pending message chains from priority addresses are always selected, regardless of their profitability.

For algorithm details, please prefer to the implementation in chain/messagepool/selection.go.