## Issue Addressed
Closes https://github.com/sigp/lighthouse/issues/2327
## Proposed Changes
This is an extension of some ideas I implemented while working on `tree-states`:
- Cache the indexed attestations from blocks in the `ConsensusContext`. Previously we were re-computing them 3-4 times over.
- Clean up `import_block` by splitting each part into `import_block_XXX`.
- Move some stuff off hot paths, specifically:
- Relocate non-essential tasks that were running between receiving the payload verification status and priming the early attester cache. These tasks are moved after the cache priming:
- Attestation observation
- Validator monitor updates
- Slasher updates
- Updating the shuffling cache
- Fork choice attestation observation now happens at the end of block verification in parallel with payload verification (this seems to save 5-10ms).
- Payload verification now happens _before_ advancing the pre-state and writing it to disk! States were previously being written eagerly and adding ~20-30ms in front of verifying the execution payload. State catchup also sometimes takes ~500ms if we get a cache miss and need to rebuild the tree hash cache.
The remaining task that's taking substantial time (~20ms) is importing the block to fork choice. I _think_ this is because of pull-tips, and we should be able to optimise it out with a clever total active balance cache in the state (which would be computed in parallel with payload verification). I've decided to leave that for future work though. For now it can be observed via the new `beacon_block_processing_post_exec_pre_attestable_seconds` metric.
Co-authored-by: Michael Sproul <micsproul@gmail.com>
## Issue Addressed
our bootnodes as of now support only ipv4. this makes it so that they support ipv6
## Proposed Changes
- Adds code necessary to update the bootnodes to run on dual stack nodes and therefore contact and store ipv6 nodes.
- Adds some metrics about connectivity type of stored peers. It might have been nice to see some metrics over the sessions but that feels out of scope right now.
## Additional Info
- some code quality improvements sneaked in since the changes seemed small
- I think it depends on the OS, but enabling mapped addresses on an ipv6 node without dual stack support enabled could fail silently, making these nodes effectively ipv6 only. In the future I'll probably change this to use two sockets, which should fail loudly
## Issue Addressed
#3704
## Proposed Changes
Adds is_syncing_finalized: bool parameter for block verification functions. Sets the payload_verification_status to Optimistic if is_syncing_finalized is true. Uses SyncState in NetworkGlobals in BeaconProcessor to retrieve the syncing status.
## Additional Info
I could implement FinalizedSignatureVerifiedBlock if you think it would be nicer.
## Issue Addressed
NA
## Proposed Changes
This PR sets out to improve the logging/metrics experience when interacting with the builder. Namely, it:
- Adds/changes metrics (see "Metrics Changes" section).
- Adds new logs which show the duration of requests to the builder/local EL.
- Refactors existing logs for consistency and so that the `parent_hash` is include in all relevant logs (we can grep for this field when trying to trace the flow of block production).
Additionally, when I was implementing this PR I noticed that we skip some verification of the builder payload in the scenario where the builder return `Ok` but the local EL returns with `Err`. Namely, we were skipping the bid signature and other values like parent hash and prev randao. In this PR I've changed it so we *always* check these values and reject the bid if they're incorrect. With these changes, we'll sometimes choose to skip a proposal rather than propose something invalid -- that's the only side-effect to the changes that I can see.
## Metrics Changes
- Changed: `execution_layer_request_times`:
- `method = "get_blinded_payload_local"`: time taken to get a payload from a local EE.
- `method = "get_blinded_payload_builder"`: time taken to get a blinded payload from a builder.
- `method = "post_blinded_payload_builder"`: time taken to get a builder to reveal a payload they've previously supplied us.
- `execution_layer_get_payload_outcome`
- `outcome = "success"`: we successfully produced a payload from a builder or local EE.
- `outcome = "failure"`: we were unable to get a payload from a builder or local EE.
- New: `execution_layer_builder_reveal_payload_outcome`
- `outcome = "success"`: a builder revealed a payload from a signed, blinded block.
- `outcome = "failure"`: the builder did not reveal the payload.
- New: `execution_layer_get_payload_source`
- `type = "builder"`: we used a payload from a builder to produce a block.
- `type = "local"`: we used a payload from a local EE to produce a block.
- New: `execution_layer_get_payload_builder_rejections` has a `reason` field to describe why we rejected a payload from a builder.
- New: `execution_layer_payload_bids` tracks the bid (in gwei) from the builder or local EE (local EE not yet supported, waiting on EEs to expose the value). Can only record values that fit inside an i64 (roughly 9 million ETH).
## Additional Info
NA
## Issue Addressed
Related to #3672
## Proposed Changes
- Added a guide to run a node. Mainly, copy and paste from 'Merge Migration' and 'Checkpoint Sync'.
- Ranked it high in ToC:
- Introduction
- Installation
- Run a Node
- Become a Validator
...
- Hid 'Merge Migration' in ToC.
## Additional Info
- Should I add/rephrase/delete something?
- Now there is some redundancy:
- 'Run a node' and 'Checkpoint Sync' contain similar information.
- Same for 'Run a node' and 'Become a Validator'.
Co-authored-by: kevinbogner <114221396+kevinbogner@users.noreply.github.com>
Co-authored-by: Michael Sproul <micsproul@gmail.com>
## Issue Addressed
#3723
## Proposed Changes
Adds a new CLI flag `--gui` which enables all the various flags required for the gui to function properly.
Currently enables the `--http` and `--validator-monitor-auto` flags.
## Issue Addressed
#3732
## Proposed Changes
Add a CLI flag to allow users to opt out of the restrictive permissions of the log files.
## Additional Info
This is not recommended for most users. The log files can contain sensitive information such as validator indices, public keys and API tokens (see #2438). However some users using a multi-user setup may find this helpful if they understand the risks involved.
## Issue Addressed
Partially addresses #3651
## Proposed Changes
Adds server-side support for light_client_bootstrap_v1 topic
## Additional Info
This PR, creates each time a bootstrap without using cache, I do not know how necessary a cache is in this case as this topic is not supposed to be called frequently and IMHO we can just prevent abuse by using the limiter, but let me know what you think or if there is any caveat to this, or if it is necessary only for the sake of good practice.
Co-authored-by: Pawan Dhananjay <pawandhananjay@gmail.com>
* add a rt is_blob_batch
* use the mixed type everywhere
* glue
* more glue
* minor fixes
* fix range tests
* filling in the gaps
* moore filling in the gaps
