Currently, the ENR of the node may not be correctly updated when specifying ipv6 fields through the CLI if an ENR exists on disk.
This remedies a bug where we were not checking for ipv6 fields when comparing whether to use an on-disk ENR or updating based on CLI configuration parameters.
Done in different PRs so that they can reviewed independently, as it's likely this won't be merged before I leave
Includes resolution for #4080
- [ ] #4299
- [ ] #4318
- [ ] #4320
Co-authored-by: Diva M <divma@protonmail.com>
Co-authored-by: Age Manning <Age@AgeManning.com>
## Issue Addressed
Add support for ipv6 and dual stack in lighthouse.
## Proposed Changes
From an user perspective, now setting an ipv6 address, optionally configuring the ports should feel exactly the same as using an ipv4 address. If listening over both ipv4 and ipv6 then the user needs to:
- use the `--listen-address` two times (ipv4 and ipv6 addresses)
- `--port6` becomes then required
- `--discovery-port6` can now be used to additionally configure the ipv6 udp port
### Rough list of code changes
- Discovery:
- Table filter and ip mode set to match the listening config.
- Ipv6 address, tcp port and udp port set in the ENR builder
- Reported addresses now check which tcp port to give to libp2p
- LH Network Service:
- Can listen over Ipv6, Ipv4, or both. This uses two sockets. Using mapped addresses is disabled from libp2p and it's the most compatible option.
- NetworkGlobals:
- No longer stores udp port since was not used at all. Instead, stores the Ipv4 and Ipv6 TCP ports.
- NetworkConfig:
- Update names to make it clear that previous udp and tcp ports in ENR were Ipv4
- Add fields to configure Ipv6 udp and tcp ports in the ENR
- Include advertised enr Ipv6 address.
- Add type to model Listening address that's either Ipv4, Ipv6 or both. A listening address includes the ip, udp port and tcp port.
- UPnP:
- Kept only for ipv4
- Cli flags:
- `--listen-addresses` now can take up to two values
- `--port` will apply to ipv4 or ipv6 if only one listening address is given. If two listening addresses are given it will apply only to Ipv4.
- `--port6` New flag required when listening over ipv4 and ipv6 that applies exclusively to Ipv6.
- `--discovery-port` will now apply to ipv4 and ipv6 if only one listening address is given.
- `--discovery-port6` New flag to configure the individual udp port of ipv6 if listening over both ipv4 and ipv6.
- `--enr-udp-port` Updated docs to specify that it only applies to ipv4. This is an old behaviour.
- `--enr-udp6-port` Added to configure the enr udp6 field.
- `--enr-tcp-port` Updated docs to specify that it only applies to ipv4. This is an old behaviour.
- `--enr-tcp6-port` Added to configure the enr tcp6 field.
- `--enr-addresses` now can take two values.
- `--enr-match` updated behaviour.
- Common:
- rename `unused_port` functions to specify that they are over ipv4.
- add functions to get unused ports over ipv6.
- Testing binaries
- Updated code to reflect network config changes and unused_port changes.
## Additional Info
TODOs:
- use two sockets in discovery. I'll get back to this and it's on https://github.com/sigp/discv5/pull/160
- lcli allow listening over two sockets in generate_bootnodes_enr
- add at least one smoke flag for ipv6 (I have tested this and works for me)
- update the book
## Issue Addressed
N/A
## Proposed Changes
Adds a cli option to disable packet filter in `lighthouse bootnode`. This is useful in running local testnets as the bootnode bans requests from the same ip(localhost) if the packet filter is enabled.
## Issue Addressed
Resolves#2094
## Proposed Changes
Fixes scripts for creating local testnets. Adds an option in `lighthouse boot_node` to run with a previously generated enr.
## Issue Addressed
#1378
## Proposed Changes
Boot node reuses code from beacon_node to initialize network config. This also enables using the network directory to store/load the enr and the private key.
## Additional Info
Note that before this PR the port cli arguments were off (the argument was named `enr-port` but used as `boot-node-enr-port`).
Therefore as port always the cli port argument was used (for both enr and listening). Now the enr-port argument can be used to overwrite the listening port as the public port others should connect to.
Last but not least note, that this restructuring reuses `ethlibp2p::NetworkConfig` that has many more options than the ones used in the boot node. For example the network config has an own `discv5_config` field that gets never used in the boot node and instead another `Discv5Config` gets created later in the boot node process.
Co-authored-by: Age Manning <Age@AgeManning.com>
